Chimney waterproofing in Braintree Town, Massachusetts that stops leaks before they start
Vapor-permeable chimney water repellent in Braintree Town, applied by CSIA-trained techs
Chimney waterproofing in Braintree Town, Massachusetts is the exterior seal that keeps freeze-thaw water out of your brick, crown, and mortar. If you have seen white staining, flaking brick faces, or a damp attic stain after a nor'easter, the masonry is already absorbing water. We apply chimney water repellent in Braintree Town after a full inspection, so the treatment goes on clean masonry and actually bonds. Most homes are done in a single visit.
What Chimney waterproofing in Braintree Town, Massachusetts actually does
Chimney waterproofing in Braintree Town, Massachusetts is a breathable masonry sealer applied to the exterior brick, mortar joints, and crown. It is not a paint or a rubber coating. The product we use, ChimneySaver water repellent, soaks into the pores of the brick and lines them so liquid water beads off while vapor still escapes. That last part matters: if you trap moisture inside a chimney, you get spalling bricks and popped mortar in two winters instead of ten. We brush the stack with a chimney brush, wash it down, let it dry, then spray or roll the repellent on in two passes.
Braintree Town chimneys take a beating. The town sits close enough to the coast that winter storms arrive with wind-driven rain, and the older brick stock around Braintree Town Center and the Washington Street Corridor was laid before modern flashing details were standard. Water gets in at the crown, the flashing, and the mortar joints, then freezes and pries the brick apart. If you have been searching for Chimney waterproofing near me Braintree Town Massachusetts because of a recurring leak, the exterior seal is usually the missing piece. It is also the cheapest line of defense you can buy.
Why Braintree Town homeowners waterproof the chimney
Waterproofing is preventive work, so the payoff shows up in the years you do not spend repairing brick. Here is what a properly applied chimney water repellent in Braintree Town buys you.
Stops freeze-thaw spalling
Brick is porous. When it soaks up rain and the temperature drops below 32 degrees, the water expands and flakes the brick face off. A repellent keeps 95 percent or more of that liquid water out, so the freeze-thaw cycle loses its grip. Homes we treat in the Highlands and Granite Woods stop shedding brick grit onto the roof within one season.
Prevents interior leak stains
Most ceiling and attic stains around a chimney start as a slow exterior leak, not a failed liner. Water tracks down the brick, hits the flashing, and finds a path inside. Sealing the stack closes the largest entry point. If you have been looking for Chimney waterproofing to prevent leaks Braintree Town, this is the step that ends the recurring stain.
Extends mortar joint life
Deteriorated mortar joints are the number one reason chimneys need tuckpointing. Water sitting in the joints softens the mortar and lets it wash out. A breathable repellent slows that process dramatically, so the joints you have now last years longer. Pair it with Chimney Tuckpointing and you reset the clock on the whole stack.
Protects the crown and cap
A crumbling chimney crown and a rusty chimney cap both fail faster when they stay wet. We seal the crown with chimney crown mix and treat the masonry below it, so the top of the chimney sheds water instead of holding it. That combination is what keeps a chimney cap and flashing doing their jobs.
How our waterproofing process works
Every job follows the same five steps, whether it is a single-family colonial in Braintree Village or a two-flue stack off Quincy Avenue. You get a written scope and a fixed price before we open a can of repellent.
Inspection
We start with a level 2 inspection using an inspection camera and a smoke chamber brush, checking the crown, flashing, cap, liner, and mortar joints against NFPA 211. You get photos of anything that needs repair before waterproofing. This step takes about 45 minutes and it is what keeps us from sealing over a problem.
Repairs first
Waterproofing only works on sound masonry. If we find cracked flashing, a failed crown, or open mortar joints, we fix those first with tuckpointing mortar, chimney crown mix, or a new stainless steel liner as needed. Skipping this step is why cheap waterproofing jobs fail in a year. We schedule the repair and the seal together so you are not paying for two mobilizations.
Surface prep
We set drop cloths, brush the stack with a chimney brush and chimney rods, and wash off dirt, algae, and efflorescence. A vacuum with a HEPA filter keeps dust out of your yard. The brick has to be dry to the touch before repellent goes on, so on humid days we wait. Prep is roughly a third of the labor on a typical job.
Application
We apply ChimneySaver water repellent with a low-pressure sprayer and back-roll it with a mortar hawk and roller to work it into the pores. Two coats, roughly 15 minutes apart. Coverage runs about 100 to 150 square feet per gallon, so a standard 30-foot stack takes two to three gallons. The whole application is usually done in two to four hours.
Cure and walkthrough
The repellent cures in about 24 hours and reaches full water resistance in 72. We walk the roof line with you, show you the before-and-after photos, and confirm the crown, cap, and flashing are all shedding water. You get a 5-year workmanship warranty on the application. If water still gets in, we come back and find out why.
Chimney waterproofing expertise you can check
MendexoLift has been waterproofing chimneys in Braintree Town since 2022, and in that time we have treated stacks on everything from 1920s brick colonials near Union Street to newer builds in Granite Woods. Our technicians train to CSIA Certified Chimney Sweep standards and work to NFPA 211 and the Massachusetts building code on every job. We carry OSHA safety certification for roof and scaffold work, and we use scaffolding or roof anchors on every stack over 20 feet. Waterproofing is not complicated, but it is unforgiving: prep it wrong and it peels, seal it wet and it traps moisture. Four years of doing it the right way is why our callbacks are rare.
- CSIA Certified Chimney Sweep training on every technician who touches your stack
- NFPA 211 level 2 inspection included before any repellent is applied
- OSHA-certified roof and scaffold work for stacks over 20 feet
- ChimneySaver and HomeSaver repellent systems, applied at manufacturer-specified coverage
- 4 years serving Braintree Town, from Braintree Town Center to the Quincy Avenue Corridor
Why Braintree Town chooses our Chimney waterproofing
Plenty of outfits will spray something on your chimney and cash the check. We inspect first, repair what is broken, and seal only sound masonry. That order is the whole difference.
We repair before we seal
Sealing over a cracked crown or open mortar joints traps water and makes the damage worse. We fix the crown, flashing, and joints first, then waterproof. That is why our applications hold up through multiple Braintree Town winters instead of one.
Fixed pricing, no surprises
You get a written price before we start. A single-stack waterproofing job in Braintree Town runs $450 to $900 in 2026 depending on height and condition, and that number does not move because we found an extra gallon of repellent. Repairs are quoted separately and approved by you first.
Local to Braintree Town
We are not driving in from an hour away. Our crews know the brick stock around South Braintree and the wind-driven rain that hits the East Braintree side of town. When you search for Chimney waterproofing services Braintree Town, you get a company that has actually worked on your neighborhood's chimneys.
Emergency response when water is winning
If a storm has opened a leak and water is coming into your ceiling, call (844) 803-2151. We run emergency Chimney waterproofing Braintree Town MA calls and can often tarp and stabilize the same day, then schedule the permanent seal once the masonry dries. Water damage gets expensive fast. Stopping it does not have to.
What our Chimney waterproofing service includes
Every waterproofing job includes the inspection, prep, and application as one package. Repairs found during the inspection are quoted separately and only happen with your approval, so you always know what you are paying for before we start.
What's Included
Level 2 inspection
A full NFPA 211 level 2 inspection of the crown, flashing, cap, liner, and mortar joints, with photos. This is what tells us whether the chimney is ready to seal or needs repair first. It takes about 45 minutes and it is included in the price.
Surface preparation
We brush the stack with a chimney brush and chimney rods, wash off dirt and efflorescence, and let the brick dry. Prep is roughly a third of the labor, and skipping it is the main reason cheap waterproofing peels within a year.
Two-coat repellent application
We spray and back-roll ChimneySaver water repellent at manufacturer coverage, about 100 to 150 square feet per gallon. Two coats, roughly 15 minutes apart, worked into the pores of the brick and mortar with a roller.
Crown and cap sealing
The crown gets sealed with chimney crown mix where needed, and we check that the cap and flashing are shedding water correctly. These are the two spots where most Braintree Town chimney leaks begin, so we do not leave them to chance.
Cleanup and walkthrough
Drop cloths come up, the HEPA vacuum handles any dust, and we walk the roof line with you. You see the before-and-after photos, get the warranty paperwork, and know exactly when to schedule the next water-bead check.
Chimney problems waterproofing solves in Braintree Town
Water is patient. It finds the same weak points on Braintree Town chimneys year after year, and the damage compounds. Here are the problems we see most and how sealing the stack puts a stop to them.
Brick faces flaking off after winter
Spalling bricks shed grit onto the roof and gutters, and each freeze-thaw cycle takes another layer off the brick. Left alone, the chimney wall thins and the structural integrity drops.
We replace the spalled units with matching brick set in refractory mortar, then apply chimney water repellent so the new brick stays dry. The repellent keeps 95 percent or more of liquid water out, which is what breaks the freeze-thaw cycle.
Recurring ceiling or attic stains near the chimney
A stain that comes back after every storm means water is still finding a path in. Drywall, insulation, and framing absorb it, and mold can start within 48 hours of a sustained leak.
We trace the leak to its source, whether that is the crown, flashing, cap, or open mortar joints. Once we repair the failure, we waterproof the stack so the same path does not reopen next season. Most Braintree Town leak calls end with a sealed chimney and a dry ceiling.
Crumbling crown and loose mortar at the top
The crown is the chimney's roof, and when it cracks, water runs straight down into the masonry. Loose mortar joints below it let that water spread through the whole stack.
We rebuild the crown with chimney crown mix and a proper overhang, repoint the deteriorated joints with tuckpointing mortar, then seal the masonry. That order matters: sealing a cracked crown just traps water underneath it.
Rusty cap and damper from constant moisture
A rusty chimney cap stops doing its job and lets rain into the flue. The damper rusts shut or open, and you end up with water in the firebox and a chimney that smells damp all summer.
We replace the cap with a stainless or copper model, repair the damper, and waterproof the exterior so the new parts are not sitting in a wet chimney. This is one of the most common combinations we fix in Braintree Town.
When Braintree Town homeowners call us for waterproofing
A homeowner in the Highlands notices brick flakes in the gutter every spring and white staining on the chimney.
That staining is efflorescence, a sign water is moving through the masonry. We inspect, confirm the joints and crown are still sound, then apply chimney water repellent in Braintree Town after a full wash-down and dry time.
The brick stops absorbing water, the efflorescence stops returning, and the stack stops shedding grit onto the roof within one season.
A family near the Washington Street Corridor gets a ceiling stain after every nor'easter and has already had the flashing patched once.
We run a level 2 inspection with an inspection camera and find the real entry point, often the crown or open mortar joints rather than the flashing. We repair what is failed, then seal the stack.
The stain does not come back after the next storm, and the homeowner stops paying for repeat patch jobs that never solved the problem.
A homeowner in South Braintree is preparing to sell and the buyer's inspector flagged the chimney as weathered.
We do a full inspection, handle any tuckpointing or crown repair the report calls out, then waterproof the stack and provide documentation of the work.
The chimney passes the follow-up look, the sale moves forward, and the new owner starts with a protected stack instead of a repair bill.
A property manager with a two-flue chimney off Quincy Avenue wants to stop annual leak complaints from tenants.
We waterproof both stacks, seal the crowns, and set up a maintenance schedule with a water-bead check at every annual inspection so the repellent gets reapplied before it fails.
Leak calls drop to zero, and the owner gets a predictable maintenance cost instead of emergency repair bills every winter.
Tools and methods we use to waterproof chimneys
Tools & Equipment
Chimney brush and chimney rods
Used to scrub dirt, algae, and efflorescence off the exterior brick before sealing. Clean masonry is the difference between a repellent that bonds and one that peels.
Inspection camera and smoke chamber brush
Lets us see the flue, smoke chamber, and hidden flashing details during the level 2 inspection without guessing. We find the actual leak path before we quote the work.
Low-pressure sprayer with mortar hawk and roller
We spray ChimneySaver water repellent and back-roll it to work the product into the pores. Back-rolling is what gets even coverage on rough brick faces.
HEPA vacuum and drop cloths
Keeps dust and debris out of your yard and off your roof during prep and cleanup. Standard on every job, not an add-on.
Scaffolding and OSHA-certified roof anchors
Required for safe work on stacks over 20 feet. We set up properly rather than leaning a ladder against your gutter and hoping.
Methods
NFPA 211 level 2 inspection
The national standard for chimney inspection, and the basis for every waterproofing quote we write. It covers accessible portions of the chimney exterior and interior, including the flue, crown, flashing, and cap. If the inspection turns up a repair, we tell you before we seal anything.
ChimneySaver vapor-permeable repellent application
ChimneySaver is a siloxane-based repellent that lines the pores of the brick so liquid water beads off while vapor escapes. We apply it in two coats at manufacturer coverage, roughly 100 to 150 square feet per gallon, once the masonry is clean and dry.
Repair-before-seal sequencing
We never waterproof over a cracked crown, open mortar joints, or failed flashing. Repairs happen first with tuckpointing mortar, chimney crown mix, or new flashing, then the seal goes on. This is why our applications hold up through multiple winters.
Water-bead testing
At every annual maintenance visit, we spray water on the stack and watch whether it beads or soaks in. Beading means the repellent is still working. Soaking in means it is time to reapply, usually every 5 to 7 years in this climate.
How Chimney waterproofing runs in Braintree Town
Braintree Town sits in a pocket of Massachusetts where winter storms arrive with wind-driven rain, and that combination is brutal on brick. Water gets pushed into the masonry from the side, not just the top, so the whole stack needs protection, not just the crown. The older housing stock around Braintree Town Center, the Union Street Area, and the Highland Avenue District was built with brick that is more porous than modern units, which is why we see spalling and efflorescence on those streets first. We work to NFPA 211 and the Massachusetts building code on every job, and we schedule waterproofing from late spring through early fall so the masonry has time to dry and cure before the first freeze. If you have been searching for the best Chimney waterproofing Braintree Town has to offer, ask any company what they do before they spray. If the answer is not inspection and repair first, keep looking.
Service Areas
Dense older housing with many pre-1950 brick chimneys. Efflorescence and spalling show up here earlier than anywhere else in town because the brick is more porous.
Elevated lots catch more wind-driven rain, so the exposed faces of the chimney take the worst of it. We often see the north and east sides failing first.
A mix of older colonials and mid-century homes. Chimneys here often have original mortar that is due for tuckpointing before waterproofing makes sense.
Closer to the coast, which means salt air and faster breakdown of both mortar and repellent. We recommend a water-bead check every year on this side of town.
Larger multi-flue chimneys on bigger lots. These jobs take more repellent and more time on the scaffold, but the process is identical.
Local Considerations
Wind-driven rain off the coast in winter
Water hits the chimney sideways and soaks into the brick faces, not just the crown. This is why we seal the full stack and not just the top, and why East Braintree chimneys need more frequent reapplication.
Freeze-thaw cycles from December through March
Water trapped in brick expands when it freezes and flakes the face off. A breathable repellent keeps that water out, which is the single most effective way to stop spalling in this climate.
Older, more porous brick in the historic neighborhoods
Pre-1950 brick absorbs water faster than modern units, so it needs waterproofing sooner and benefits more from it. We adjust coverage and dry time based on how thirsty the masonry is.
Humid summers that slow cure time
Repellent needs dry masonry to bond. On humid July and August days we may wait an extra day between wash-down and application, which is why we schedule waterproofing in the drier stretches of late spring and early fall.
Spalling brick chimney in Braintree Highlands
A 1940s brick chimney was shedding grit onto the roof every spring, with roughly 15 spalled brick faces on the north side and open mortar joints across the upper third. The homeowner had patched the flashing twice with no result.
We replaced the spalled units with matching brick, repointed about 40 joints with tuckpointing mortar, and applied two coats of chimney water repellent. Two winters later the brick still beads water and no new grit has appeared in the gutters.
Maintenance & Follow-up
Recheck water beading every spring. Based on the exposure on this lot, we expect the next reapplication around year six.
A cracked chimney crown was letting water run down into the masonry, showing up as a ceiling stain after every heavy rain. The damper had rusted and the firebox smelled damp all summer.
We rebuilt the crown with chimney crown mix and a proper overhang, replaced the damper, and waterproofed the stack. The ceiling stain has not returned through two storm seasons, and the firebox is dry.
Maintenance & Follow-up
Annual inspection with a water-bead test. Crowns in this climate should be checked every fall before the first freeze.
A two-flue chimney on a rental property generated leak complaints every winter. The cap was rusted through, the flashing had pulled away on one side, and the brick was holding water after every storm.
We replaced the cap with stainless, repaired the flashing, and sealed both stacks with chimney water repellent. Leak calls dropped to zero over the following two winters, and the owner moved to a scheduled maintenance plan.
Maintenance & Follow-up
Water-bead check at every annual inspection, with reapplication expected every 5 to 7 years depending on exposure.
How much does Chimney waterproofing cost in Braintree Town Massachusetts?
Most single-stack jobs run $450 to $900 in 2026, and two-flue chimneys run $700 to $1,300. The price depends on stack height, how much prep the brick needs, and whether we find crown or flashing repairs first. That range includes the inspection, surface prep, two coats of repellent, and a 5-year workmanship warranty. Repairs, if needed, are quoted separately before we start.
How often should I apply chimney water repellent in Braintree Town?
Every 5 to 7 years for a brick chimney in this climate. Coastal wind-driven rain and freeze-thaw cycles break the repellent down faster than in drier parts of Massachusetts, so we check water absorption at every annual inspection. If water stops beading on the brick, it is time to reapply. Reapplication is cheaper than the first job because the prep is lighter.
Who does Chimney waterproofing near me in Braintree Town MA?
MendexoLift does, and we have since 2022. We cover Braintree Town Center, Braintree Highlands, South Braintree, East Braintree, West Braintree, North Braintree, Braintree Village, Granite Woods, and the neighborhoods along Washington Street, Commercial Street, Liberty Street, Union Street, Highland Avenue, and the Quincy Avenue Corridor. Call (844) 803-2151 and we will schedule an inspection at your address.
Does Chimney waterproofing prevent water damage in Braintree Town?
It prevents the most common kind: water soaking into brick and mortar from outside. A breathable repellent keeps 95 percent or more of liquid water out while letting the chimney breathe, which stops spalling bricks and slows mortar joint failure. It does not fix a failed liner or a cracked crown, so we repair those first. Done in the right order, it is the cheapest water damage prevention you can buy.
Credentials and reviews
Certifications
Reviews
They inspected first, found the crown was the real problem, fixed it, and then waterproofed. No pressure, no upsell. The ceiling stain has not come back through two storm seasons.
Repointed about 40 joints and sealed our 1930s chimney. The brick beads water now instead of soaking it up. Fair price and they cleaned up everything before they left.
Called on a Friday with water coming in during a storm. They tarped it the same day and came back Monday to do the permanent waterproofing and flashing repair. Exactly what you want from a local company.
Two-flue chimney on a rental property, leak complaints every winter. After they sealed both stacks and replaced the cap, zero calls. Worth every dollar.
Related Services
Chimney Repair Near Me
Waterproofing protects sound masonry, but it cannot fix what is already broken. If your Braintree Town chimney has cracked brick or a loose cap, we repair it first, then seal it, so the waterproofing has something solid to bond to.
Chimney Repair Near MeChimney Masonry Repair
Spalling bricks and washed-out joints are the damage waterproofing is designed to prevent. When we find them in Braintree Town, we rebuild the affected courses with firebrick and refractory mortar, then apply chimney water repellent to the repaired stack.
Chimney Masonry RepairChimney Crown Repair
A crumbling chimney crown is the number one entry point for water in Braintree Town. We pour a new crown with chimney crown mix and overhang, then waterproof the masonry below it. That combination is what actually keeps the stack dry.
Chimney Crown RepairChimney Relining
Waterproofing keeps water out of the masonry, but it does nothing for a damaged chimney liner. If your liner is cracked or missing, we install a stainless steel liner to NFPA 211, then seal the exterior so the whole system is protected.
Chimney ReliningChimney Cap Repair
A rusty chimney cap lets rain straight into the flue. We repair or replace caps with stainless or copper models, then waterproof the stack below. For Braintree Town homes, that two-part fix ends most chimney leaks in one visit.
Chimney Cap RepairChimney Maintenance
Annual maintenance is how you avoid big repair bills. Our Braintree Town maintenance visits include a level 2 inspection, a chimney sweep, and a water-bead test on the existing repellent, so you know exactly when it is time to reapply.
Chimney MaintenanceFireplace Repair
Water that gets into a chimney often ends up in the firebox, rusting the damper and staining the brick. We repair the fireplace, then waterproof the exterior so the same leak does not come back next winter.
Fireplace RepairEmergency Chimney Repair
When a storm opens a leak and water is running into your ceiling, call us. We tarp and stabilize the chimney, then schedule the permanent waterproofing and repairs once the masonry dries. Same-day response is common around Braintree Town.
Emergency Chimney Repair24/7 Chimney Repair
Chimney emergencies do not wait for business hours. Our 24/7 line covers Braintree Town for active leaks, fallen caps, and storm damage. We stop the water first, then plan the waterproofing and repair work for daylight.
24/7 Chimney RepairChimney Leak Repair
We trace chimney leaks to their source: crown, flashing, cap, or masonry. Once we find it in Braintree Town, we repair the failure and apply chimney water repellent to the stack so the same path does not reopen.
Chimney Leak RepairProfessional Chimney Repair
Waterproofing is only as good as the masonry under it. Our professional chimney repair work in Braintree Town follows NFPA 211 and the Massachusetts building code, so the structure you seal is sound to begin with.
Professional Chimney RepairChimney Inspection Service
Every waterproofing job starts with a level 2 inspection. We check the crown, flashing, cap, liner, and mortar joints with an inspection camera, then tell you honestly whether you need repairs before sealing.
Chimney Inspection ServiceChimney Cleaning Service
Creosote buildup and waterproofing are separate problems, but they get solved on the same visit. We sweep the flue with a chimney brush and Sooteater, then prep and seal the exterior while we are already on the roof.
Chimney Cleaning ServiceChimney Restoration
When a Braintree Town chimney has gone too long without protection, restoration rebuilds it: new crown, repointed joints, replaced brick, and a fresh waterproofing seal. It costs more than sealing alone, but it resets the chimney for decades.
Chimney RestorationChimney Liner Repair
A damaged chimney liner is a fire hazard, not a waterproofing issue. We repair or reline the flue to NFPA 211, then waterproof the exterior masonry so water never reaches the liner from outside.
Chimney Liner RepairFireplace Restoration
Water damage inside a firebox shows up as rusted dampers and stained brick. We restore the fireplace and seal the exterior with chimney water repellent, so the interior work stays dry.
Fireplace RestorationFireplace Installation
New fireplace installations in Braintree Town should be waterproofed from day one. We install the unit, then seal the exterior masonry and flashing so the first winter does not undo the work.
Fireplace InstallationChimney Tuckpointing
Tuckpointing replaces deteriorated mortar joints with fresh tuckpointing mortar. It is the repair that has to happen before waterproofing on most older Braintree Town chimneys, because sealing crumbling joints just traps water behind them.
Chimney TuckpointingChimney Mortar Repair
Loose or missing mortar lets water straight into the chimney wall. We grind out the bad joints with an angle grinder and repoint them, then waterproof the stack so the new mortar cures protected.
Chimney Mortar RepairChimney Sweep
A chimney sweep clears creosote and blockages so the flue drafts correctly. We pair it with waterproofing on Braintree Town homes because both jobs put a technician on the roof, which saves you a second service call.
Chimney SweepChimney Sweep Near Me
If you are searching for a chimney sweep near me in Braintree Town, we handle the sweep and the waterproofing in one visit. You get a clean flue and a sealed exterior without scheduling two companies.
Chimney Sweep Near MeChimney Flashing Repair
Cracked chimney flashing is a top cause of roof leaks around the stack. We repair or replace the flashing, seal the seams, and waterproof the chimney above it so water has nowhere to enter.
Chimney Flashing RepairChimney Cap Installation
A properly fitted chimney cap keeps rain, birds, and debris out of the flue. We install stainless or copper caps on Braintree Town chimneys, then waterproof the stack so the cap is not fighting a wet crown.
Chimney Cap InstallationResidential Chimney Repair
Our residential chimney repair covers the full stack: crown, brick, mortar, flashing, cap, and liner. Waterproofing is the finishing step that protects the repair work from the next Braintree Town winter.
Residential Chimney RepairBrick Chimney Repair
Spalling bricks get replaced with matching units set in refractory mortar. Once the brickwork is sound, we apply chimney water repellent so the new brick does not start spalling in three years.
Brick Chimney RepairRoof Chimney Repair
Roof-level chimney work means flashing, counter-flashing, and the roof-to-chimney transition. We repair those details and waterproof the stack, which is where most Braintree Town roof leaks around a chimney actually start.
Roof Chimney RepairChimney Damper Repair
A rusted damper is often the first sign water is getting into the flue. We repair or replace the damper, then waterproof the exterior so the new one is not sitting in a damp chimney.
Chimney Damper RepairMetal Chimney Repair
Metal chimneys need different treatment than brick. We repair the sections, seals, and storm collars, then apply the right protective coating for the material instead of a masonry repellent that will not bond.
Metal Chimney RepairSame Day Chimney Repair
For active leaks and storm damage in Braintree Town, we offer same-day chimney repair when the schedule allows. We stop the water first, then come back to waterproof and finish the repair once conditions are right.
Same Day Chimney RepairGet Chimney waterproofing in Braintree Town, Massachusetts before the next storm
Water damage never gets cheaper with time. We inspect, repair what is broken, and seal the stack with a breathable repellent backed by a 5-year workmanship warranty. Call (844) 803-2151 and we will schedule your Braintree Town chimney waterproofing this week.